Genda FP 14000 Power Amplifikatör 2x4600W/4 ohm
Genda FP 14000 Power Amplifikatör 2x4600W/4 ohm
| Model | FP 14000 |
| General | |
| Number of amplifier channels | 2 |
| Peak total output all channels driven | 14000 W |
| Peak output voltage per channel | 195 V |
| Max output current per channel | 90 A peak |
| Max output power (all channels driven) | |
| 16 ohms | 1200 W |
| 8 ohms | 2350 W |
| 4 ohms | 4600 W |
| 2 ohms | 7000 W |
| Max output power bridged | |
| 16 ohms | 4700 W |
| 8 ohms | 8800 W |
| 4 ohms | 14000 W |
| 2 ohms | Not recommended1 |
| Performance | |
| THD 20 Hz - 20 kHz at 1W | <0.1% |
| THD at 1 kHz and 1 dB below clipping | <0.05% |
| Signal to Noise Ratio | >112 dBA |
| Channel separation (Crosstalk) at 1 kHz | >70 dB |
| Frequency response (1 W into 8 ohms) + 0 / -3 dB | 2 Hz - 34.2 kHz |
| Output impedance @ 100 Hz | 19 mOhm |
| Gain, Sensitivity and Limiters | |
| VPL, selectable per ch | 195, 170, 140, 116, 100, 80, 66, 54 V |
| VPL, when bridged2 | 390, 340, 280, 232, 200, 160, 132, 108 V |
| Voltage Peak Limiter mode (per ch.) | Hard / Soft |
| Amplifier gain selectable (all channels) – rear-panel switches2 | 23, 26, 29, 32, 35, 38, 41, 44 dB |
| Default gain | 38 dB |
| Level adjustment (per channel) | Front-panel potentiometer, 31 position detented from -inf to |
| Connectors and Buttons | |
| Input connectors (per ch.) | 3-pin XLR, electronically balanced |
| Output connectors (per ch.) | Neutrik speakON / binding post |
| Output bridge mode | A+B - Ch. A is signal input source. A+B, C+D - Ch.’s A and C are input source |
| NomadLink network | On board, 2 x RJ45 connectors IN and OUT |
| Intelligent fans (on/off) | Yes, depending on presence of output signal |
| Power on/off and Remote enable on/off | Individual switches on front-panel |
| Cooling | Dual fan, front to rear airflow, no filter required, temperature controlled speed |
| Front-panel user interface | |
| Common | NomadLink Network; Power Average Limiter (PAL)4; Power on |
| Per channel | Signal present / High-impedance; -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL): Very High Frequency (VHF); High temperature; Fault; Mute |
| Power | |
| Operating voltage, 230 V / 115 V nominal3 | 130-265 V / 65 -135 V |
| Minimum power-up voltage, 230 V / 115 V | 171 V / 85 V |
| Power Average Limiter (PAL)4 | Yes |
| Soft-start / Inrush Current Draw | Yes / max. 5 A |
| Mains connector | 230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock |
| Dimensions | |
| Dimensions | W: 483 mm (19”), H: 88 mm (2 U), D: 396 mm (15.6”) |
| Weight | |
| Weight | 12 kg (26.4 lbs) |
| Finish | |
| Finish | Black painted steel chassis with black painted steel / aluminum front |
| Approvals | |
| Approvals | CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC |
1:Regarding n.r. (not recommended) notes: The amplifier will be fully operational in bridge-mode into 2 ohm and high impedance (Hi-Z) loads, but due to physical constraints in the construction, the max. output power will not be significantly higher than running individual channels and therefore this mode of operation is not recommended.
2:Automatic -6 dB gain compensation when bridging channels.
3:Separate 230 V or 115 V versions available. Not selectable on the amplifier.
4:PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker. Refer to the FP+ Operation Manual section 7.5.8 Power Average Limiter (PAL) for more information.
